产品名称：
日本NS日进钻石平底铣刀
产品型号：DCHR230
发布日期：2022-10-30
产品摘要：
日本NS金刚石涂层 2刃长颈立铣刀，采用独特的金刚石涂层，在石墨和高硅铝合金加工中表现出高耐久性。颈部后部类型，适用于狭窄和深加工。
商品详情
相关商品
CDHR230钻石涂层 2刃长颈平底铣刀图片与尺寸
可对应石墨和复合材料加工的，钻石涂层长颈平底铣刀
CDHR230钻石涂层 2刃长颈平底铣刀订货型号
| 产品代码 Code No. | (D)外径 Dia. | (C)颈长 Under Neck Length | (&)刃长 Length of Cut | (d2)颈径 Neck Dial | (Y)颈角Neck Taper Angle | (d)柄径 Shank Dial | (L)全长 Overall Length |
| 05-000-00502 | 0.5 | 2 | 1 | 0.46 | 12 | 4 | 45 |
| 05-00200-00504 | 4 | 1 | 0.46 | 12° | 4 | 45 | |
| 05-000-00506 | 6 | 1 | 0.46 | 12° | 4 | 45 | |
| 05-00200-01004 | 1 | 4 | 2 | 0.95 | 12° | 4 | 50 |
| 05-00200-01006 | 6 | 2 | 0.95 | 12° | 4 | 50 | |
| 05-00200-01008 | 8 | 2 | 0.95 | 12° | 4 | 50 | |
| 05-00200-01506 | 1.5 | 6 | B | 1.45 | 12° | 4 | 50 |
| 05-000-01512 | 12 | 3 | 1.45 | 12° | 4 | 50 | |
| 05-00200-01520 | 20 | B | 1.45 | 12° | 4 | 60 | |
| 05-00200-02006 | 2 | 6 | 4 | 1.94 | 12° | 4 | 50 |
| 05-00200-02010 | 10 | 4 | 1.94 | 12° | 4 | 50 | |
| 05-00200-02016 | 16 | 4 | 1.94 | 12° | 4 | 60 | |
| 05-00200-02020 | 20 | 4 | 1.94 | 12° | 4 | 60 | |
| 05-000-03016 | 3 | 16 | 6 | 2.85 | 12° | 6 | 60 |
| 05-00200-03030 | 30 | 6 | 2.85 | 12° | 6 | 70 | |
| 05-000-04020 | 4 | 20 | 8 | 3.8 | 12° | 6 | 60 |
| 05-00200-04040 | 40 | 8 | 3.8 | 12° | 6 | 90 | |
| 05-000-06030 | 6 | 30 | 12 | 5.8 | 12° | 6 | 90 |
| 12° |
注意事项：
请指定DCHR230外径（D）×颈长（ℓ1，※(γ)为参考值。
加工案例 W-027
| 加工工程 Process | 圆柱部相加工、 Ruglig gSyineu | 粗加工 Roughing | 中精加工 Sem-inishing | 精加工 Finishing |
| 使用刀具 Too" | DCSE235 $6 | DCHR230 01x10 | ||
| 生轴转速[min] Spinde speed | 8,000 | 20,000 | ||
| 进给速度[mm/minj Feed | 600 | 2,000 | 1,000 | 800 |
| 切深量apx ae[mm] Dephof t | 8x0.5 | 0.2x0.6 | 0.05x0.2 | |
| 加工长度[m], Maching length | 7 | 67 | 18 | |
| 加工时间 Machining time | 5分钟 Smin | 1 小时5分钟 1hr5min | 10分钟 10min | |
CDHR230钻石涂层 2刃长颈平底铣刀切削参数参考表
| DCHR230 | |||||||||||||||
| 切削参数参考表 Recommended Milling Conditions | |||||||||||||||
| 加工材料 Work Matenal | 石墨 Graphite | 铝合金压铸件 Aluminum Alloy Die Casting | |||||||||||||
| 等高线粗加工 Contour Uine Roughing | 沟槽切削 Sloting | 等高线粗加工 Contour Uine Roughing | 沟槽切削 Slotting | ||||||||||||
| 刃径 Dia. | 有效长 Effective Length | 主轴转速 $nde pee d | 进蛤速度 Feed | 切深量 Depth of Cut | 主轴转速 $pnde | 进给速度 Feed | 切深量 Degthoaut | 主轴转速 $ginde Sped | 进给速度 Feed | 切深量 Depth of Cut | 主轴转速 $pnde Sped | 进给速度 Feed | 切深量 Deghoh ut | ||
| min *' | mm/mi n | apmm | apmm | min" | mm/min | apmm | min' | mmimin | apmm | apmm | min" | mn/m n | apmm | ||
| 0.5 | 2 | 30,0000 | 1,200 | 0.1 | 0.3 | 30.000 | 800 | 0.1 | 20.000 | 1000 | 0.03 | 0.3 | 20,000 | 500 | 0.03 |
| 4 | 30.000 | 1,000 | 0.05 | 0.3 | 30,000 | 600 | 0.05 | 20.000 | 800 | 0.01 | 0.3 | 20,000 | 400 | 0.01 | |
| 6 | 25.000 | 8001 | 0.03 | 0.3 | 25.000 | 500 | 0.03 | 20,000 | 600 | 0.01 | 0.3 | 20.00 | 300 | 0.01 | |
| 1 | 4 | 30.000 | 2.500 | 0.2 | 0.6 | 30.000 | 1.500 | 0.2 | 20.000 | 2.00 | 0.15 | 0.6 | 20.000 | 1,200 | 0.15 |
| 6 | 25.0 | 2.0000 | 0.2 | 0.6 | 25.000 | 1,200 | 0.2 | 20.000 | 1,500 | 0.1 | 0.6 | 20.000 | 1.000 | 0.1 | |
| 8 | 20.000 | 1,500 | 0.1 | 0.6 | 20.000 | 1,000 | 0.1 | 20.000 | 1,000 | 0.07 | 0.6 | 20.000 | 700 | 0.07 | |
| 10 | 20.0000 | 1,000 | 0.1 | 0.6 | 20.0000 | 600 | 0.1 | 20,0000 | 800 | 0.05 | 0.6 | 20.000 | 500 | 0.05 | |
| 1.5 | 6 | 25.000 | 2.500 | 0.3 | 25.00 | 1.600 | 0.3 | 20,000 | 2.000 | 0.2 | 一 | 20.000 | 1.500 | 0.2 | |
| 12 | 16.000 | 1,800 | 0.2 | 一 | 16.000 | 1,000 | 0.2 | 16.000 | 1.500 | 0.05 | 1 | 16.000 | 1000 | 0.05 | |
| 20 | 12.000 | 1,000 | 0.1 | 1 | 12.000 | 600 | 0.1 | 12.000 | 800 | 0.02 | 一 | 12.000 | 500 | 0.02 | |
| 2 | 6 | 20.000 | 3.0000 | 0.5 | 1.2 | 20.000 | 2,000 | 0.5 | 20,00 | 2,000 | 0.5 | 1.2 | 20,000 | 1,500 | 0.5 |
| 10 | 20,000 | 2,500 | 0.5 | 1.2 | 20,000 | 1,600 | 0.5 | 20,000 | 1.500 | 0.3 | 1.2 | 20.000 | 1,000 | 0.3 | |
| 16 | 18.000 | 1,800 | 0.3 | 1.2 | 18.000 | 1,200 | 0.3 | 15.000 | 1,200 | 0.07 | 1.2 | 15.000 | 800 | 0.07 | |
| 20 | 15.000 | 1,200 | 0.2 | 1.2 | 15.000 | 800 | 0.2 | 10.000 | 1,000 | 0.03 | 1.2 | 10.000 | 600 | 0.03 | |
| 3 | 16 | 20.000 | 3.000 | 0.5 | 2 | 20.000 | 2.000 | 0.5 | 18,000 | 2,000 | 0.5 | 2 | 18.000 | 1.500 | 0.5 |
| 30 | 15.000 | 1,500 | 0.3 | 2 | 15.000 | 10000 | 0.3 | 10.00 | 1000 | 0.2 | 2 | 10.000 | 600 | 0.2 | |
| 4 | 20 | 18.000 | 3,000 | 0.8 | 2.5 | 18.000 | 2,000 | 0.8 | 16,000 | 2,000 | 0.8 | 2.5 | 16.000 | 1.500 | 0.8 |
| 40 | 9.000 | 1,500 | 0.4 | 2.5 | 9,000 | 10000 | 0.4 | 8,000 | 1,000 | 0.4 | 2.5 | 8.000 | 600 | 0.4 | |
| 6 | 30 | 16.000 | 3.0000 | 4 | 16,000 | 2,000 | 1 | 12,000 | 2,000 | 4 | 12,000 | 1.500 | 一 | ||
| 备注 | 系加工石墨时，请使用石墨专用的加工机床。 此外,进行加工或者操作时为了防止粉尘飞扬或者被吸入身体,请使用吸尘器和防尘口罩。 照石墨加工建议采用干式切削。 累如果力具发生廊刃,或者需要高精度加工时,请降低进给速度。此外，主轴转速过低时i也以相同的比率降低。 | ||||||||||||||
| Graphite should be machined by the machining center designed for graphite machining. When handling with graphte material, dust cllector and rspiator are recommended to protect againt graphte dust.Air tblow colin i5 recommended for the maching of graphte KAdjust both spindle speed and feed at the same rate when chattering.Slow down the feed for high accurate machining to avoid breakage of work piece, | |||||||||||||||
备注：因厂家会在没有任何提前通知的情况下更改产品包装、产地或者一些附件，本公司不能确保客户收到的货物与德锐克精密工具有限公司网站提供的产品图片、产地、附件说明等完全一致。若本网站没有及时更新，敬请谅解！
新品推荐
一周热销排行
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
