韩国昌汉大型自动平面磨床CGM-640产品特点:
优良的材质、通过时效处理更好的提高钢性的铸件,高精密度的高钢性立柱,双V型导轨设计的的工作台、实现高低速高精密作业。
■主轴头的自动进给提供了最大的便利
■通过编码器使立柱转换方向
独立液压单元配有冷却系统、可以有效防止震动和油温对机器精密度的干扰,根据人体工学式的设计机器
■具备粗磨与精磨、更广范围的研磨条件
■自动运转时显示现在位置和研磨进行情况
系统可以直观方便的的实现位置表示和全自动频率控制(粗磨量、精磨量、精磨切入点、无火花工作、频率停止后的磨头位置)
各个导轨面的自动润滑,将主轴集中摆放在机器正面,方便控制的集中式控制面板,接近传感器使工作台转换方向。
韩国昌汉大型自动平面磨床CGM-640产品配置:
冷却装置 | Coolant system | 1套/1SET |
砂轮 | Wheel | 1片/1PC |
法兰 | Wheel flange | 1个/1PC |
顶出螺栓 | Wheel extractor | 1个/1PC |
砂轮平衡架和棒 | Balance base & arbor | 1套/1SET |
垫铁 | Leveling block | 5个/5PCS |
地脚螺丝 | Leveling bolt | 5个/5PCS |
工具及工具箱 | Tool box set | 1套/1SET |
High quality cast iron,nib reinforced,annealing heat treated for maximum nigidity of operationEfficient high rigidity column stricture by structural analysis obtains high precision
Designed overhanging type V-V sliding structure table realizes high precision operation in both high and low speed
Automatic down feed of wheel head gives maximum operation convenience
Column movements reversible by Encoder (Memory section Setting)
Separate hydraulic tank and oil temperature radiator system avoids the transmission of heat and vibration to the machine.(Standard)
Convenient grinding thanks to ergonomic design
Suitable for wide range of grinding from heavy grinding to precision grinding
Current position and grinding state is constantly displayed during automatic cycle
Control system for full automatic cycle with position displays assures intuitively easy operation.(Rough grinding,Fine grinding,Fine grinding position,Spark-out and Cycle stop head position)
Automatic continuous lubrication on all slide ways
Handle intensively arranged on the front of machine
Centralized control panel for easy operation
Table movements reversible by proximity sensor
韩国昌汉大型自动平面磨床CGM-640产品规格型号:
MODEL | 640SH 640SHD | |||
工作台面积 | Table clamping surface | 680x400mm | ||
最大移动距离(左右x前后) | Maximum travel(XxY) | 760x480mm | ||
电磁吸盘大小 | Magnet chuck | 600x400mm | ||
主轴中心距到工作台上面最大距离 | Max. distance between spindle center and table | 610mm | ||
工作台 Table | T槽尺寸(宽*高) | T Slot size (WidexNumber) | 18mmx3n | |
左右移动速度 | X-Axis Traverse speed range | 5~25m/min | ||
前后手动进给(一刻度) | Cross feed handle wheel (Graduation) | 0.02mm | ||
前后手动进给(一圈) | Cross feed handle wheel(Revolution) | 4mm | ||
前后间歇进给速度 | Cross feed increment traverse volume | 0.03~10mm/step | ||
前后连续进给速度 | Cross feed continuous traverse speed | 0.1~1.0m/min | ||
前后最大急速进给速度 | Maximum rapid traverse speed | 1000mm/min | ||
上下 Head | 上下手动进给(一刻度) | Down feed handle wheel (Graduation) | 0.005mm | |
上下手动进给(一圈) | Down feed handle wheel (Revolution) | 1mm | ||
上下自动一圈切入量 | Automatic feed per traverse volume | - 0.001~0.5mm | ||
上下急速仅给速度 | Maximum rapid traverse speed | 500mm | ||
主轴 | 砂轮尺寸 | Grinding wheel dimension | Ø305x20~38txΦ127mm | |
Spindle | 主轴转速(50Hz) | 50Hz Revolutions per minute | 1450rpm | |
主轴转速(60Hz) | 60Hz Revolutions per minute | 1750rpm | ||
主轴电机 | Spindle motor | 5Hpx4P | ||
液压油泵用电机 | Hydraulic pump motor | 2Hpx | 6P | |
总消耗电力 | Total walk power | 7Kw | 8Kw | |
机器重量 | Machine net weight(approx.) | 3800Kgf | 3900Kgf | |
包装总重量 | Packing gross weight (approx.) | 4100Kgf | 4200Kgf | |
占地面积(左右x前后x上下) | Floor space(LxWxH) | 100 | 2050mm | |
包装面积(左右x前后x上下) | Packing space(LxWxH) | 2400 | x2450mm |